Automobilbau 1,0 A LDO-Regler mit variablem Ausgang - BD18HC0MEFJ-M

BDxxHC0MEFJ-M ist ein LDO-Regler mit 1,0 A Ausgangsstrom. Die Genauigkeit der Ausgangsspannung liegt bei ±1 %. Mit einem externen Widerstand kann die Ausgangsspannung beliebig festgelegt werden (von 1,5 V bis 7,0 V). Der Gehäusetyp ist: HTSOP-J8. Eine Überstrom-Schutzschaltung (als Schutz des IC gegen Schäden durch Kurzschluss), ein Schaltstrom-AN/AUS-Schalter (setzt die Schaltung im Abschaltmodus auf 0 µA) und eine thermische Abschaltung (als Schutz des IC gegen Hitzeschäden durch Überlast) sind integriert. Er kann mit keramischen Kondensatoren verwendet werden, ist platzsparend und hat eine längere Lebensdauer.

Minimale Gehäusemenge
BD18HC0MEFJ-ME2 Active HTSOP-J8 2500 2500 Taping Ja
Grade Automotive
Breakdown Voltage(Max.)[V] 10.0
ch 1
Vin(Min.)[V] 4.5
Vin(Max.)[V] 8.0
Vout (Typ.) [V] 1.8
Vout Precision ±3.0%
Iout(Max.)[A] 1.0
Circuit Current[mA] 0.6
Shutdown Function Yes
Thermal Shut-down Yes
Over Current Protection Yes
Over Voltage Protection No
Discharge Function No
Soft Start Yes
I/O Voltage Difference (Typ.)[V] 0.6(Io=1A)
Ripple Rejection [dB] 60.0
Load Regulation[mV] 25(Io=0 to 1A)
Input Capacitor[µF] 1.0
Output Capacitor[µF] 1.0
Operating Temperature (Min.)[°C] -40
Operating Temperature (Max.)[°C] 105
  • ・ High accuracy reference voltage circuit
    ・ Built-in Over Current Protection circuit (OCP)
    ・ Built-in Thermal Shut Down circuit (TSD)
    ・ With shut down switch
    ・ AEC-Q100 Qualified
Weitere neue/aktualisierte Produkte im Zusammenhang mit Energieverwaltung / Power Management
TEILENUMMER Produktname Gehäuse Datenblatt Lieferbare Bestände
BD00HC0MEFJ-M Automobilbau 1,0 A LDO-Regler mit variablem Ausgang HTSOP-J8   Kaufen
BD15HC0MEFJ-M Automobilbau 1,0 A LDO-Regler mit variablem Ausgang HTSOP-J8   Kaufen
BD25HC0MEFJ-M Automobilbau 1,0 A LDO-Regler mit variablem Ausgang HTSOP-J8   Kaufen
BD30HC0MEFJ-M Automobilbau 1,0 A LDO-Regler mit variablem Ausgang HTSOP-J8   Kaufen
BD33HC0MEFJ-M Automobilbau 1,0 A LDO-Regler mit variablem Ausgang HTSOP-J8   Kaufen
BD50HC0MEFJ-M Automobilbau 1,0 A LDO-Regler mit variablem Ausgang HTSOP-J8   Kaufen
Neue Produkte:
Technische Daten
Table of resistance for output voltage setting on linear regulator Ics

This application notes provide tables for each series so that it is easy to set the resistance value for the output voltage setting from various internal reference voltages VREF.

Thermal Resistance

The definition and how to use thermal resistance and thermal characterization parameter of packages for ROHM’s integrated circuit are described in this application note.

BDxxGC0, BDxxGA5, BDxxGA3, BDxxHC5, BDxxHC0,BDxxHA5, BDxxHA3, BDxxIC0, BDxxIA5 Series PCB Layout

The basic terminal configuration of a linear regulator IC consists of four parts: input, output, GND, and feedback…

Basics of Linear Regulators

A linear regulator, also referred to as a "three-terminal regulator" or "dropper," is a power supply long known to many designers owning to its simple circuitry and ease of use...

Linear Regulator Specifications

Very important information such as maximum ratings, operating conditions and characteristic graphs are described in the table.

Reverse Voltage Protection

A linear regulator integrated circuit (IC) is a DC-to-DC buck converter system that reduces a DC supply from higher voltage level to a lower voltage level...

Simple Test Method for Estimating the Stability of Linear Regulators

Low drop-out (LDO) regulators developed back in the age when large-capacitance multi-layer ceramic capacitors (hereinafter, MLCCs) were uncommon cause a phase delay, leading to oscillation when connected to a low-ESR capacitor like an MLCC...

Thermal Calculation for Linear Regulator

The loss in linear regulators increases as the difference between the input and output voltages increases. Since most of the loss is converted to heat, a very large amount of heat may be generated in some conditions...

Power Source ON/OFF Characteristics for Linear Regulator

When a linear regulator IC is turned ON, the electric charge is stored in the output capacitor and the output voltage increases up to the specified value.

BAxxCC0 Series Circuit Using a Ceramic Output Capacitor

This application note proposes a circuit using an output ceramic capacitor that allows a stable phase compensation.

Measurement Method for Phase Margin with Frequency Response Analyzer (FRA)

This application note introduces a method for easily measuring the phase margin with a Frequency Response Analyzer (FRA) made by NF Corporation.

Connecting LDOs in Parallel

Provides some hints on how to connect LDOs in parallel.